Project 4G63T PG1 Updated
- scientist
- moderator

- Posts: 4599
- Joined: Mon Aug 13, 2007 1:31 am
Project 4G63T PG1 Updated
Well....almost everyone knows i acquired a 88 Galant VR4....but its also not so great of condition [thumbsdown]
Well day one of the project was basically towing it over to our super secret bat cave [2clap] ok i know it isn't funny.
Project Parts List For first round of parts
Ignition
Custom Coil on Plug
Engine
King Bearings Race bearings
ARP Hardware
Eagle Rods
Wiseco Pistons
Mitsubishi MLS head gasket
Street Tuned Motorsports (STM) Oil Cooler
Fuel:
Injector Dynamics 1000CC
Fuel Lab FPR
Turbo:
FP DSM 3065 Turbo
Custom Oil feedline with heat barrier sheild (Prevent manifold from burning into line and rupturing it)
FP Inline Oil filter
FP Race Manifold
Auto Clinic Custom braided -6an water feed and return lines
Custom 4" intake
Exhaust
3" O2 housing back exhaust
FP 2.5" V band O2 Elbow
Tial 44MM wastegate
Suspension
KYB AGX (Temporary)
Tuners Nation Subframe Bushings
Drive train:
4 Bolt LSD rear end with axles and cups
5 Lug conversion
Solid Shifter cable bushings
Competition Clutch Twin Disk
Tuners Nation Master to slave cylinder Charcoal braided clutch line
Tuners Nation charcoal braided brake lines
4WS Elimination[/u]
Exterior
93 Galant LS Crystal headlights
Custom Front Lip
Electronics
Omni 4 Bar map sensor
GM IAT sensor
90 EPROM Ecu
MOATES Ostrich 2.0 Emulator and MOATES Chip burner
Relocated Battery to Trunk
Well day one of the project was basically towing it over to our super secret bat cave [2clap] ok i know it isn't funny.
Project Parts List For first round of parts
Ignition
Custom Coil on Plug
Engine
King Bearings Race bearings
ARP Hardware
Eagle Rods
Wiseco Pistons
Mitsubishi MLS head gasket
Street Tuned Motorsports (STM) Oil Cooler
Fuel:
Injector Dynamics 1000CC
Fuel Lab FPR
Turbo:
FP DSM 3065 Turbo
Custom Oil feedline with heat barrier sheild (Prevent manifold from burning into line and rupturing it)
FP Inline Oil filter
FP Race Manifold
Auto Clinic Custom braided -6an water feed and return lines
Custom 4" intake
Exhaust
3" O2 housing back exhaust
FP 2.5" V band O2 Elbow
Tial 44MM wastegate
Suspension
KYB AGX (Temporary)
Tuners Nation Subframe Bushings
Drive train:
4 Bolt LSD rear end with axles and cups
5 Lug conversion
Solid Shifter cable bushings
Competition Clutch Twin Disk
Tuners Nation Master to slave cylinder Charcoal braided clutch line
Tuners Nation charcoal braided brake lines
4WS Elimination[/u]
Exterior
93 Galant LS Crystal headlights
Custom Front Lip
Electronics
Omni 4 Bar map sensor
GM IAT sensor
90 EPROM Ecu
MOATES Ostrich 2.0 Emulator and MOATES Chip burner
Relocated Battery to Trunk
Last edited by scientist on Sun Oct 10, 2010 12:16 pm, edited 13 times in total.
/////////Ralliart
- club4g63
- You can't stop posting can you

- Posts: 1033
- Joined: Sat Aug 25, 2007 8:27 am
Re: Project 4G63T
good luck i have been in this car and belive me it has fire just a lil heavy but u can make a thig happen they see the oldschool they spoke off in the secret place aswell ,nice.
- punch
- Power Junkie

- Posts: 318
- Joined: Sun Sep 30, 2007 4:06 pm
Re: Project 4G63T
It has begun, young gunz project mitsu #2
- kenwin
- grease Monkey

- Posts: 72
- Joined: Tue Aug 14, 2007 1:28 pm
Re: Project 4G63T
eyy congrats on the purchase,,i expect lots of development on this project...Also like the old school scene ![Thumbs Up [thumbsup]](./images/smilies/thumbsup.gif)
-
hilliuse
- Power Junkie

- Posts: 355
- Joined: Fri Sep 01, 2006 10:10 pm
Re: Project 4G63T
i remember this car
lets see what yall do with it
lets see what yall do with it
-
Cly-dee
- Power Junkie

- Posts: 337
- Joined: Thu May 11, 2017 11:38 am
Re: Project 4G63T
nice project sci
u have alot of work to do but the body lookin in good shape man just under the hood. I didnt kno it was that car, i used to see it around.
- djphattraxx
- Power Junkie

- Posts: 618
- Joined: Fri Sep 01, 2006 9:51 am
Re: Project 4G63T
Congrats my boy !
Very good start!
- SF5
- You can't stop posting can you

- Posts: 1309
- Joined: Fri Oct 13, 2006 2:15 pm
Re: Project 4G63T
How's it sound? You got a MAF?
-
EVO2ENVY
- Power Junkie

- Posts: 236
- Joined: Thu Aug 23, 2007 4:24 pm
Re: Project 4G63T
Good luck to you bro. It's a bit on the heavy side but it has great potential
.
-
ceelos
Re: Project 4G63T
DcaTSiAWD wrote: How's it sound? You got a MAF?
No MAF as yet. is also off timing and the plugs were in the wrong firing order. but we got it started. it also has a few other things here and there that have to get done.
