![[dwl]](./images/smilies/pofl.gif "dieing with laughter"){kind=small}
Project 4G63T PG1 Updated
-
Lil Stig
- moderator
- Posts: 363
- Joined: Wed Aug 15, 2007 10:24 am
Re: Project 4G63T PG1 Updated
everything comin along nicely so far. but sci the headliner good all u have to do is bring it by Flucky for a shape up and u good as Phat-i suggested lol..
-
TheGoodGuy
- You can't stop posting can you
- Posts: 1543
- Joined: Fri Mar 14, 2008 11:24 am
Re: Project 4G63T PG1 Updated
Niceness.. cannot wait to see that engine built.
"Its not the size of the engine that matters... its how much shit you can bolt to it....."
-
scientist
- moderator
- Posts: 4599
- Joined: Mon Aug 13, 2007 1:31 am
Re: Project 4G63T PG1 Updated
Well not much happened today,
Polished the bearings, installed them, sent the balance shafts out to be machined into a BSE elimination kit. (Kinda like the AMS one which still maintains the shaft but without the weight)
We also put the crank onto the block, install the new BS bearings. Will torque everything down tommorow. Hopefully tommorow i will get a call about the pistons. And will find out how much it will cost to machine the balance shafts. I also need to cut a stub out of forward facing part of the left mount because of the head studs to allow the head to drop down onto them.
Will have video soon
Polished the bearings, installed them, sent the balance shafts out to be machined into a BSE elimination kit. (Kinda like the AMS one which still maintains the shaft but without the weight)
We also put the crank onto the block, install the new BS bearings. Will torque everything down tommorow. Hopefully tommorow i will get a call about the pistons. And will find out how much it will cost to machine the balance shafts. I also need to cut a stub out of forward facing part of the left mount because of the head studs to allow the head to drop down onto them.
Will have video soon
/////////Ralliart
-
TheGoodGuy
- You can't stop posting can you
- Posts: 1543
- Joined: Fri Mar 14, 2008 11:24 am
Re: Project 4G63T PG1 Updated
Update..
You do not have the required permissions to view the files attached to this post.
"Its not the size of the engine that matters... its how much shit you can bolt to it....."
-
TROJAN - X
- Power Junkie
- Posts: 795
- Joined: Mon Mar 17, 2008 2:27 pm
Re: Project 4G63T PG1 Updated
thanks god that was editied
OH YEAH - sure feels like 10 to me.....
NF² ........ NO FACE - NO FEAR
NF² ........ NO FACE - NO FEAR
-
scientist
- moderator
- Posts: 4599
- Joined: Mon Aug 13, 2007 1:31 am
![[bff]](./images/smilies/friends.gif "Best Friends"){kind=small}
-
TROJAN - X
- Power Junkie
- Posts: 795
- Joined: Mon Mar 17, 2008 2:27 pm
Re: Project 4G63T PG1 Updated
starring sci and cee
onlydom mad scientist and mr cee it all
cant wait for the 1st episode![[drool]](./images/smilies/drool.gif "drool")
![[interesting]](./images/smilies/eat.gif "Very Interesting")
onlydom mad scientist and mr cee it all
cant wait for the 1st episode
OH YEAH - sure feels like 10 to me.....
NF² ........ NO FACE - NO FEAR
NF² ........ NO FACE - NO FEAR
-
scientist
- moderator
- Posts: 4599
- Joined: Mon Aug 13, 2007 1:31 am
Re: Project 4G63T PG1 Updated
Well not much happened today. We finished removing the valve springs and retainers, I started cleaning up the valves to prep them for grinding. Removed the cam plug to install the new one. Will take the chance to finish clean up the head and remove all the excess silicone put on there.
/////////Ralliart
-
motion sickness
- Power Junkie
- Posts: 767
- Joined: Tue Aug 14, 2007 11:19 pm
Re: Project 4G63T PG1 Updated
Didn't see a torque wrench used in the vid. Did you guys later torque the caps down to spec and in sequence?
-
scientist
- moderator
- Posts: 4599
- Joined: Mon Aug 13, 2007 1:31 am
Re: Project 4G63T PG1 Updated
Lol ofcourse everything was torqued to spec. The vid was also edited cause Two forum members were misbehaving and didn't want it shown. (Scotch is a hell of a thing)motion sickness wrote:Didn't see a torque wrench used in the vid. Did you guys later torque the caps down to spec and in sequence?
We are building everything on the service manual and making sure everything is within serviceable spec. if the are not they aren't then we have to send it off to the machine shop
/////////Ralliart